No.162 SLIP TESTER
JIS P8147
- This tester is used to measure the friction coefficient of plastic film and paper according to the inclination method.
- By inclining the inclination board at a constant speed, the static friction coefficient can be measured at the tangent at which the test specimen starts to slip.
Specification
| Specifications are subject to change without notice. | |
| Sled | W60 mm, L100 mm, Mass 1,000 g |
| Slip Surface Affective Length | 600 mm (Scale attached) *Slip Detection Sensors are installed by default. |
| Inclination Angle | 0 to 70° (Analog Scale, unit 0.2°) |
| Inclination Speed | 1 °/s |
| Power Source | AC 100 V, 1-Phase, 3 A, 50/60 Hz |
| Dimensions/ Weight (Approx.) | W750 × D350 × H425 mm, 29 kg |
No.162-FS SLIP TESTER (HORIZONTAL METHOD)
JIS K7125、P8147、ASTM D3247、ISO 8295、TAPPI-T816
- This tester is used to measure the friction coefficient of plastic film and paper according to the horizontal method.
- The operator is to attach the test specimen to the sliding surface and sliding sled, then pull the sled with a metal wire that is connected to a load cell to acquire the static coefficient of friction and dynamic coefficient of friction.
Specification
| Specifications are subject to change without notice. | ||
| Test Method | Paper and Paperboard | Plastic Film |
| Abrading Head | W60 mm, L100 mm, Mass 1,000 g | 63 × 63 mm (Abrading Surface 40 cm2) Mass 200 ± 2 g (1.96 ± 0.02 N) |
| Flat Board | W200 mm, L380 mm | W200 mm, L380 mm |
| Specimen | Surface: W100 mm, L250 mm Sled: W60 mm, L120 mm |
W80 mm, L200 mm, T0.5 mm or Less |
| Friction Measuring | Load Cell: Max. 10 N, 20 N, 50 N | Load Cell: Max. 10 N, 20 N, 50 N |
| Speed | 10.0 ± 0.2 mm/min | 100 ± 10 mm/min or 500 ± 10 mm/min |
| Accessories | ― | Accessory Plate (Mass Less than 5 g) |
| Option | Variable Speed Spec, Software, Recorder, Heating Plate Spec. | Variable Speed Spec, Software, Recorder, Heating Plate Spec. |
| Power Source | AC 100 V, 1-Phase, 5 A, 50/60 Hz | AC 100 V, 1-Phase, 5 A, 50/60 Hz |
| Dimensions/ Weight (Approx.) | W600 × D375 × H415 mm, 35 kg | W600 × D375 × H415 mm, 35 kg |
No.162-OY O-Y PULL SLIP TESTER
JIS A1454、A1509-12
- This tester evaluates the slippage of floor material.
- The coefficient of slip resistance can be measured by the maximum tensile load at the point when the test specimen and the slip head touch each other.
- When the test specimen and the slip head touch each other, the slip head is pulled 18° upwards at a prescript load speed to acquire the maximum tensile load for the calculation of the coefficient of slip resistance (C.S.R) As an option, slippage of clay tile can also be tested.
- In addition to the usual C.S.R, C.S.R-B can also be calculated.
Specification
| Specifications are subject to change without notice. | |
| Specimen | 100 × 120 mm (Ceramic Tile: 90 × 135 mm) |
| Sled | 80 × 70 mm |
| Vertical Weight Load | Initial 294 N (30 kgf) to Max. 785 N (80 kgf) (Standard: 785 N) |
| Tension Angle | 18° |
| Tension Load Measuring | Load Cell, Max. 5 kN (Scale 1 N) |
| Tension Load Speed | 785 N/s |
| Software | Windows Compatible |
| Option | Specimen Holder (Standard and Nosing Edge type), Ceramic Tile Spec (with Sled, Testing Powder, C.S.R.-B Measuring Software) |
| Power Source | AC 100 V, 1-Phase, 10 A, 50/60 Hz |
| Dimensions/ Weight (Approx.) | Tester Body: W1,610 × D580 × H1,600 mm, 428 kg Control Box: W650 × D550 × H240 mm, 16 kg |
No.162-S5 5 HANGINGS SLIP TESTER
JIS P8147、ASTM D1894、D3248、TAPPI-(T503)、(T542)、T815
- This tester is the digital and 5 hanging version of the SLIP TESTER.
- The tester enables the operator to measure the static friction coefficient of 5 test specimens per test.
- The static friction coefficient can be shown on the LCD screen and can also be printed out.
- The computer system of the tester will also calculate the average static friction coefficient of the 5 test specimens.
Specification
| Specifications are subject to change without notice. | |
| Sled | W41 mm, L26 mm, Mass 150 g, 5 pcs |
| Inclination Board | W320 mm, L325 mm |
| Inclination Angle | 0 to 70° (Scale 0.1°) |
| Inclination Speed | 1°/s |
| Return Speed | 3°/s, Automatic Return System |
| Power Source | AC 100 V, 1-Phase, 10 A, 50/60 Hz |
| Dimensions/ Weight (Approx.) | W580 × D700 × H380 mm, 50 kg |