List of custom products in the past|YASUDA SEIKI SEISAKUSHO LTD. providing you the best material testing equipment.

No.306-L FPC FLEXING TESTER(WITH REFRIGERATING MACHINE)

JIS C5016

No.306-L FPC FLEXING TESTER(WITH REFRIGERATING MACHINE)

  • This model is equipped with a low temp.chamber for testing at low tempertures.

Specification

Specifications are subject to change without notice.
Model No.306-L FPC FLEXING TESTER(WITH REFRIGERATING MACHINE)
Hanging 4Hanging(2Hanging Simultaneous Drive×2)
Flexing Radius Max. 10 mm
Flexing Speed Max. 60 cpm
Flexing Length Reciprocate 20(± 10) mm、40(± 20) mm、60(± 30) mm
Piston Option
Counter 6 Digits Preset Counter
Temperature Range -35 to 60 °C(Refrigerator)
Option Conduction Device(for FPC)
Power Source AC 200 V、3-Phase、30 A、50/60 Hz
Dimensions/Weight(Approx.) W1,160 × D730 × H1,200 mm/ 250 kg

Inquiry Form

No.324 CANADIAN STANDARD FREENESS TESTER

JIS P8121, TAPPI-T227, ISO 5267-2

No.324 CANADIAN STANDARD FREENESS TESTER

  • This tester is used to evaluate the freeness of pulp.
  • By filtrating a certain amount of test specimen, the operator is to read the amount of discharged test specimen that flew out from the side tube.
  • The operator is to use the correction table so that the test data is calibrated to the Canadian standard freeness conditions of a standard density of 0.3 % and standard temperature of 20 °C.

Specification

Specimen Bone-Dried 3 g, Concentration 0.3 %, Solution 1,000 ml
Drainage Chamber Inner Diameter φ101.5 ± 0.4 mm
H127 mm (Wire Screen to Rim)
Air Cock Hole φ4.7 mm or More
Wire Screen φ111.0 ± 0.5 mm, 80 mesh
Measuring Funnel Opening φ204 mm
Overall L280 mm
Bottom Orifice φ3.05 ± 0.01 mm
Side Orifice Inner Diameter φ13 mm
Accessories Measuring Cylinder, Jug
Option Stand
Dimensions/ Weight (Approx.) W300 × D270 × H720 mm/ 22 kg

Inquiry Form

No.325 SCHOPPER-RIEGLER TYPE FREENESS TESTER

JIS P8121, ISO 5267-1

No.325 SCHOPPER-RIEGLER TYPE FREENESS TESTER

  • This tester is used to evaluate the freeness of pulp. By filtrating a certain amount of test specimen, the operator is to read the amount of discharged test specimen that flew out from the side tube to calculate the Schopper freeness.
  • The down flow of the test specimen will be done by pulling up the circular coned valve upwards.

Specification

Specimen Bone-Dried 2 g, Concentration 0.2 %, Solution 1,000 ml
Drainage Chamber Inner Diameter φ137 mm、H150 mm(Wire Screen to Rim)
Wire Screen φ112.9 ± 0.1 mm, 100 mesh
Measuring Funnel Opening φ115 mm, H150 mm, Bottom Orifice φ2.4 mm
Accessories Measuring Cylinder, Jug
Dimensions/ Weight (Approx.) W250 × D460 × H1,100 mm/ 18 kg

Inquiry Form

No.330 PULP SCREENING TESTER

JIS P8207

No.330 PULP SCREENING TESTER

  • This tester is used to evaluate the fiber length distribution of paper making pulp.
  • The 4 tanks which have different size of metal mesh, screens the test specimen.
  • The operator is to measure the absolute dry mass of pulp in each tank to calculate the screening degree.

Specification

Specime Bone-Dried 10 g, Concentration 1 %, 1,000 ml
Test Bath 191 × 191 × 290 mm
Stirrer Rotation Speed 800 rpm
Water Feed 8.3 L/min
Wire Screen Diameter φ102 mm
Screen Combination 710, 355, 180, 106 µm/
1180, 600, 300, 150 µm/
1400, 850, 600, 300 µm
Option Flow Meter, Timer
Power Source AC 100 V, 1-Phase, 15 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,350 × D300 × H1,400 mm, 120 kg

Inquiry Form

No.338 AUTOMATIC K.B.B. SIZING TESTER

J.TAPPI-No.13/1, JIS K8122

No.338 AUTOMATIC K.B.B. SIZING TESTER

  • This tester is used to measure the K.B.B. size (water resistance) of paper and paperboard.
  • The operator is to clamp the test specimen into one pair of dissimilar metal and soak the surface of the test specimen with an electrolyte liquid that is at a constant density.
  • The tester will automatically measure the time it took to flow electricity due to the penetration of the electrolyte liquid.

Specification

Specimen 90 × 90 mm
Moveable Electrode (Anode) Bronze Made
Fixed Electrode (Cathode) Zinc Made, For One Side Penetration, For Both Side Penetration
Micro Current Meter 0 to 100 µm
Timer Max. 99999.9 sec, Digital Display Ver.
Electrolyte Solution Potassium Chloride Solution (1 %)
Power Source AC 100 V, 1-Phase, 3 A, 50/60 Hz
Dimensions/ Weight (Approx.) W400 × D350 × H500 mm, 20 kg

Inquiry Form

No.404 MULLEN TYPE BURSTING STRENGTH TESTER (FOR TEXTILE)

JIS (L1018), L1085, L1096, (JASO)

No.404 MULLEN TYPE BURSTING STRENGTH TESTER FOR TEXTILE

  • This tester is used to evaluate the bursting strength of textile according to the Mullen’s method.
  • The operator is to tighten the test specimen to the tightening board and pressurize it with a rubber membrane mediator.
  • The maximum pressure when the test specimen bursts subtracted by the strength of the rubber membrane will be the bursting strength of the test specimen.

Specification

Specifications are subject to change without notice.
Specimen 150 × 150 mm
Clamp Upper φ30.48 ± 0.03 mm
Lower φ31.50 + 0.25 mm
Upper and Lower both with 60°V Groove
Pressing Speed 98 ± 4 ml/min
Pressure Gauge Choose 2 kinds (0.3, 0.6, 1.4, 2.0, 4.5 and 7.0 MPa)
Accessories Rubber Membrane: 10 pcs, Membrane Height Gauge, Fixing Tool
Option Digital Pressure Gauge, Pneumatic Clamp Spec (YPO)
Power Source AC 100 V, 1-Phase, 10 A, 50/60 Hz
Dimensions/ Weight (Approx.) W560 × D580 × H570 mm, 104 kg
W400 × D500 × H560 mm, 85 kg (YPO)

Inquiry Form

No.542-CR AUTOMATIC FILM APPLICATOR (CERAMIC PLATE TYPE)

No.542-CR AUTOMATIC FILM APPLICATOR (CERAMIC PLATE TYPE)

No.542-CR AUTOMATIC FILM APPLICATOR (CERAMIC PLATE TYPE)

JIS K5101, (K5400), ASTM D823
  • This machine enables the operator to make a coating surface of ink, colorant, and paint automatically.
  • Since the machine coats at a constant speed and pressure, it solves the problems of unevenness and individual variability when coating.
  • The material of the coating plate is porous ceramics which enables to coat super thin coat paper and polyester film in vacuum state.
  • The machine can be used together with a BARCOATER and APPLICATOR.

Specification

Specifications are subject to change without notice.
Maximum Test Panel Size A4 size: W270 × L360 mm (Material: Porous Ceramics)
A3 size: W355 × L516 mm (Material: Porous Ceramics)
Coating Area A4 size: W200 × L300 mm
A3 size: W300 × L450 mm
Length Setting Sensor Attached (can make 300 to 450 mm)
Coating Speed 20 to 300 mm/s (60 Hz), 20 to 260 mm/s (50 Hz)
Safety Device (Option) Slip type Torque Limiter (70 N)
Accessories Weights for Barcoater (3 kinds), Jig for Applicator, Scraper, Spatula
Option Vacuum Pump, Barcoater, Applicator
Power Source AC 100 V, 1-Phase, 10 to 15 A, 50/60 Hz
Dimensions/ Weight (Approx.) A4 size: W570 × D490 × H430 mm, 50 kg
A3 size: W720 × D590 × H430 mm, 65 kg

Inquiry Form

No.601 BELT FATIGUE TESTER

No.601 BELT FATIGUE TESTER

  • This tester is to evaluate the fatigue strength by flexing the steel belt used in tires.
  • The specimen is bent in half and flexed through horizontal movement while being tensioned.

Specification

Hangings 12 Hangings, Single Driving Type
Flexing Length 120 mm
Flexing Speed 165 times/min
Test Load Max. 60 kgf
Temperature Range 0 to 100 °C (Refrigerator)
Power Source AC 200 V, 3-Phase, 30 A, 50/60 Hz
Dimensions/ Weight (Approx.) W1,900 × D950 × H1,850 mm/ 1,000 kg

Inquiry Form

No.662 HINGE CAP ENDURANCE TESTER

No.662 HINGE CAP ENDURANCE TESTER

  • This tester is used for conducting endurance tests on hinge caps used for stationary and medicine containers.
  • Attachment jigs can be custom made to meet various cap shapes.

Specification

Cap Opening Angle 120° (Option: Free Angle)
Opening Speed 50 times/min (Option: Speed Controller)
Option Break Detection Feature
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W250 × D365 × H450 mm/ 15 kg

Inquiry Form

No.664 NAIL PENETRATION TESTER

No.664 NAIL PENETRATION TESTER

  • This tester is used to demonstrate a short-circuit, one cause of accidental combustion, by penetrating lithium-ion batteries.
  • By penetrating the separators within batteries which sustain insulation, a short circuit is created.
  • The test is conducted to examine the results by comparing penetrating conditions such as depth, speed, nail size and materials.

Specification

Depth Max. 10 mm
Speed 0.2, 2, 20 mm/sec
Nail Size Max. φ4.0 mm
Power Source AC 100 V, 1-Phase, 5 A, 50/60 Hz
Dimensions/ Weight (Approx.) W530 × D400 × H710 mm/ 50 kg

Inquiry Form

Contact Us

For over 70 years, Yasuda Seiki’s testing machines have supported quality control and research & development across various industries, meeting the diverse needs of our clients.